- Hits: 5101
ICS
Research Groups & Projects
Airship Based & Satellite-Based Communication Platforms
ICS-SAT Poster (May 2019) (as pdf)
Open Tasks for finishing prototype system:
مسألة |
موارد البشرية الداخلية المطلوبة |
الكلفة المواد وتوكيل العمل لجهة خارجية |
السنة |
TEMOLeb-Mintad Gas filling |
2 Technicians, 4 MM (man months) |
5000$ |
2019 |
TEMOLeb-Mintad& TEMOLeb-SAT solar panels and system |
- |
2000$ (عماد نصوح) |
2019 |
TEMOLeb-Mintad Control System development & Validation (simulink/scilab) |
Eng., 5 MM |
400$ |
2019 |
TEMOLeb-Mintad Actuators, Wings integration |
2 Technicians, 2 MM |
1000$ |
2019 |
TEMOLeb-Mintad Sensors integration |
Eng., 1 MM |
300$ |
2019 |
TEMOLeb-SAT Actuator (chem.) |
1 Technician, 1 MM |
1500$ |
2019 |
TEMOLeb-SAT Platform Integration |
1 Technician, 1/2 MM |
500$ |
2019 |
TEMOLeb-Mintad Telemetry Unit |
2 Eng., 6 MM |
3000$ |
2020 |
TEMOLeb-SAT Telemetry Unit |
2 Eng., 6 MM |
3000$ |
2020 |
TEMOLeb-Mintad COM Unit (Payload) |
2020 |
||
TEMOLeb-SAT COM Unit (Payload) |
2020 |
COM System
Time Plan for COM System (Last update: 16.2.2020)
Title |
Description |
Estimated Time |
Status |
Task 1: Introduction |
|||
HackRF |
Introduce HackRF and getting start with, a brochure summarize the main info should be prepared and established |
5 days |
Done |
SDR (Software Defined Radio) |
Introduce and understand SDR workflow and check for its available software |
5 days |
Done |
Task 2: Getting Start |
|||
Receiving signal |
Use available SDR software to receiving signal using HackRF |
2 days |
Done |
Transmitting signal |
Use available SDR software to transmitting signal using HackRF |
2 days |
Done |
Pentoo OS |
Prepare Pentoo OS on a machine or USB image to be used with the HackRF |
2 days |
Done |
GnuRadio |
Getting start with GnuRadio compain and make some tutorials |
3 days |
Done |
Raspberry&GnuRadio |
Install GnuRadio on Raspberry Pi OS and make some testes |
4 days |
In progress |
Task 3: System 1 (Send and receive system “separately”) |
|||
Make a Sender |
Build a system to send a RF signal using a HackRF and Raspberry Pi. |
4 days |
|
Make a Receiver |
Build a system to receive a RF signal using a HackRF and developed SDR software |
7 days |
|
Task 4: System 2 (Send\Receive system) |
|||
Raspberry S\R |
Update the Raspberry Pi system to make it two way communication sys (send\receive) |
3 days |
|
SDR software S\R |
Update the developed SDR software to make it two way communication sys. (send\Receive) |
3 days |
|
Task 5: System 3: Lotte System |
|||
Arduino > Raspberry |
Connect Arduino to Raspberry and send and receive data from it using USB connection |
5 days |
|
Raspberry > HackRF |
Use HackRF to send Arduino data, and to receive command for it |
10 days |
|
HackRF > Gui |
Use a Windows developed software to receive sent data from the raspberry side to be access |
10 days |
|
Total time: 65 days, Spent time: 20 days, Remaining time: 45 days
Ambulance & Emergency Communication Systems
Institute Director
Eng. Mahmoud Jandal Zohby
Email: This email address is being protected from spambots. You need JavaScript enabled to view it.
Tel. +961 3 671 621